Envision Peripherals 95 User Manual

EN9110 EN9110 19” LCD Monitor User’s Manual By Envision Peripherals, Inc. www.envisionmonitor.com

EN9110 9 Attaching The Optional Wall Mount Arm (not supplied) Follow these steps to finish installing the wall mounting arm: 1. Pl

EN9110 10 INSTALLATION INSTRUCTIONS • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s

EN9110 11OPERATING INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the side of

EN9110 12 FRONT PANEL CONTROL • Power Button: Press this button to switch the monitor’s power ON or OFF. • MENU / ENTER : Activate OSD m

EN9110 13 1. Press the MENU-button to activate the OSD window. See figure 5. 2. Press or to select the desired function. See figure 5

EN9110 14 Below describes the function of each OSD icon. 1. Contrast Adjust the picture contrast. 2. Brightness Adjust the picture br

EN9110 15 Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allow

EN9110 16TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution Power LED is not on *Check if the Power Switch is in the ON position

EN9110 17 Screen image is not centered or sized properly. *Adjust pixel frequency (CLOCK) and FOCUS or press hot-key (AUTO) Picture has color de

EN9110 18 NO SIGNAL 1. Check that the signal-cable is properly connected , If the connector is loose, tighten the connector’s screws. 2.

EN9110 1Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio

EN9110 191024 × 768 75Hz 1024 × 768 85Hz 1280 × 1024 60Hz 1280 × 1024 75Hz 1280 × 1024 85Hz 1152 × 864 75Hz 1280 × 960 60Hz 1280 × 960 85H

EN9110 20 FOR FIRST TIME INSTALL : This is a Plug & Play LCD monitor. Turn off the PC then connect the cables. Power on the PC and it w

EN9110 21APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 48cm(19.0") Pixel pitch 0.294mm( H )x 0.294mm( V )

EN9110 22 Switch • Auto Adjust Key • / Brightness • / Contrast • Power Button • MENU/ Exit External Controls: Functions • Contrast • Brightn

EN9110 23 STANDARD RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY Dos-mode 640 × 400 31.47kHz 70.0Hz Dos-mode 720 x 400 31.47kHz 70.0H

EN9110 24 1561011 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PI N NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Detect

EN9110 258. N.C. 20. TMDS Data 5- 9. TMDS Data 1- 21. TMDS Data 5+ 10. TMDS Data 1+ 22. TMDS Clock Shield 11. TMDS Data 1/3 Shield 23. TM

EN9110 2 ! Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. !

EN9110 3 • For maximum protection, repackage your monitor as it was originally packed at the factory. • To keep the monitor looking new, period

EN9110 4 The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluorescent li

EN9110 5 INSTALLATION INSTRUCTIONS SWIVEL BASE Install Remove Figure 1 Installing and Removing the Swivel Base POWERCORD Po

EN9110 6 PREPARING TO INSTALL THE CABLES 1. Remove the wall mounting hole cover. 2. Remove the cable cover. INSTALLATI

EN9110 7 CABLE CONNECTIONS 1 – Connect the DC-jack power cable into DC-IN connector on the back of the monitor. 2. Connect one end of

EN9110 8 Preparing To Install The Optional Wall Mount Arm (Not Included) CONNECTIONS This monitor can be attached to a wall mounting